Monday, October 22, 2012

Types of Weirs

Waterworks was built across the river to the completeness or shunt, and are made to raise the water level with a fixed threshold so that the river water can be tapped and fed by gravity to the irrigation network. Excess water is transferred to downstream waterfall with a swimming eject in order to reduce energy.
There are 2 types or types of fixed weir sill structure of the shape are:
Fixed threshold of the straight edge to the right edge of the river means that as the threshold is a straight line connecting the two points by the river.
Threshold fixed winding like a sawtooth. This type is required when the length threshold is insufficient and usually to wide river with a small but substantial water flow. So by using this type will be obtained length threshold larger main, so we will get a large discharge capacity of devolution. Given the physical form and character hydrolysis threshold, it is advisable weir type of chainsaw is used on the channel.
In terms applied in the river must meet the following requirements:
Debit relatively stable
Do not take the form of material floating tree trunks
The effectiveness of the weir length is limited to water depths chainsaw certain.
Vertical Motion weir
This weir weir consists of a body with a low fixed threshold is equipped with doors that can be moved vertically and radially. This type has a double function, which regulate water level in relation to the dam upstream flood water levels and elevating the river water level to do with tapping water for various purposes. Field operations carried out by opening the door all at great flood or partially open door at medium and small floods. The door is fully closed at normal time, which is for the benefit of tapping the water. Weir type of motion is only distinguished from the form of doors, among others:
Sliding doors or sliding, widely used for the width and height of the openings are small and medium. Pursued the door not too heavy because it would require a larger lift equipment and expensive. Should the door fairly light but has a high stiffness that is not easily removed when shaking the dynamic force of water flow.
Radial doors, have curved doors (arc) with the arm joints door embedded in the wing walls or pillars. Construction like this is so that leaves the door lighter to removed using a cable or chain. Homing to the door can also be done with a hydraulic push and pull mechanical equipment that is embedded in the wing walls or pillars.
Rubber dam (weir Horizontal Motion)
Rubber dam has two main parts, namely:
The body is made of rubber dam
Shaped concrete foundation slab concrete as a rubber tube holder and include a control room with some equipment (machines) to control expands and mengempisnya rubber tube.
This dam serves raise water levels by body swell dam and lower the water by means shrunken. Weir body made of rubber tubes can be filled with air or water. The process of filling the air or water from the air or the water pump is equipped with a control instrument air or water (manometer).
Weir Bottom Sieve
This form of the weir spillway weir equipped with fishing line and filter. This weir water passed through the filter to make the water tank in the form of fishing line across the river and the water flow to the river to take to the irrigation network.
Field operations performed by allowing sediment and rock jumped over the weir, the water was expected to enter the fishing line. High sediment deposited on the sand catcher channels that periodically washed into a river again.

Dam construction

Barricade is a building of water with complete built across a river or a shunt that deliberately to raise the water level or to get high jump. Classification Weir:
A. Barricade by function divided into three:
* weir tapper
* Weir divider flood
* Retaining dam pairs
B. Weir structure:
* fixed weir
* weir motion
* weir combination
* Weir flower deflated
* Bottom intake weir
Building the physical infrastructure of the water is needed in the management of water resources.
The building is part of the spillway chainsaw waterworks, such as dam or spillway dam that serves to pass the river flow is controlled, the layout of the building is toothed like saws to increase the transfer capacity by extending the effective width of spillway.
Weir type saws are fixed weir spillway layout lighthouse resembles a sawtooth width to obtain a longer effective spillway.
There are some parts in the weir
* Body building weirs
* Intake building
* Rinse building
* building Supplies
Mercu weir dam is the top of the body where the flow of hicks can overflow to downstream. Its function as a determinant of minimum water level.
Forms lighthouse fixed weir:
Mercu round with one or two fingers to rounding
Mercu ogee type, SAF
Mercu width threshold
Lighthouse weir shape commonly used in Indonesia, which form rounded summit. This is because:
simple shape More resistant to impact rock gelundung Resistant to scratching or abrasion
High Mercu Weir
High lighthouse weir (p), which is the height between the floor elevation hillbilly / hick weir in the river bottom and summit elevation.
In determining the height of the lighthouse weir should consider the:
The need for obtaining discharge tapping and high press
High-energy needs flushing
High water inundation will occur
Perfection flow on the weir etc.
High lighthouse weir is recommended no more than 4.00 meters and a minimum of 0.5 H Long Mercu Weir
Long lighthouse dam or weir is also called the span width, the distance between the two walls of the base of the weir (abutment), including the width of the building and its pillars rinse.
building intake
Intake building is a building that serves as the weir stream tapping, to regulate the importation of water and sediment.
Consists of floor / baseline, doors, flood walls, the placement of the door pillars, saqmpah strainer, bridge waitress, raumah doors, and other fixtures.

Supplementary Planning Building

Complement the building is a building that is created as a way of supporting irrigation. There's several buildings complement of which is building a cross. Building cross consists of several building types include:
1. Culverts
Culverts in the form of closed channels, the transition at the entrance and exit. Culverts will follow the slope of the line as possible. Culverts serve as an open channel for the building did not sink. Culverts full flow when the outlet if the water in the sink or higher and upstream culvert length. Loss of high-energy total for culvert drowning is the number of missing at the entrance, friction losses plus loss on corners sewer.
2. building Falls
Building falls can be combined with other buildings such as cribs, culverts and bridges to reduce overall costs.
3. chamfer
Flum is a sectional gutters or artificial channel in which water flows with a free surface, which is across the basin, canal, river, road or along the hillside. This building can be supported by pillars or other construction. Flem and gutters or steel and concrete used to carry a small discharge. For ducts greater use of concrete or steel gutters. Gutters that come with the transition in and out. It may take protection against scour at close distances downstream of the building, it depends on the speed and soil properties. Depending on the height loss of available energy and operational cost, Chambers cuts planned by the same broad-sectional area channel, only its dimensions as small as possible. Sometimes the gutters planned building small spillway to regulate water levels and discharge at the downstream chamfer. The building can be made of concrete or steel pipe.
4. Siphon
Siphon used to drain water passing under the road, through the river or in the exhaust duct. Flow in Siphon follow the principles of flow in the channel is closed. Between channels and Siphon on income and expenditure required matching transition. Loss of high energy Siphon covers loss due to friction, and loss on Siphon twists and water loss on the transition in and out. Siphon order to function properly, the building should not be entered into the air. Siphon mouth should be below the water level upstream and mouth Siphon in upstream and downstream order made ​​streamlines. The depth of water above the top of Siphon (water seal) and the surface of the water depends on the slope and size Siphon. Siphon can be made of steel or reinforced concrete. Siphon should be used only to carry the flow channel or channels cut across where the exhaust can not be used culverts, bridges or gutters.
5. got Tilt
In the rugged terrain in which high-energy big difference must be addressed in a short distance and tertiary channel follows the slope of the terrain, sloping gutter will be required. Got siring consists of the entry, the transition, and a normal part of me grim.
6. road Inspection
Layout also includes tertiary road planning and road inspection farmers. Operation and maintenance of channels and tertiary buildings in need of inspection road along the irrigation canal to get to the box located at the tip / downstream. Because the vehicle is in use is a bicycle or motorcycle, then the width of the inspection is taken approximately 1.5 to 2.0 m. The road inspection for tertiary canal built with thick gravel base layer and 0.20 m in order to be strong enough. Best gravel for road construction material is selected from natural alluvial river that flows in the project area. The road inspection for tertiary channels can also be constructed with a base layer of gravel and / or Class B Aggregate foundation layer thickness of 0:20 m so strong. The stones that are too large loaf or ugly graded gravel should be avoided. In flat areas or swamps high street should be taken from 0.3 to 0.5 m above the surrounding ground.

Sunday, January 8, 2012

How To Calculate Concrete Method B.O.W

Koef B.O.W based materials:

Cement = 0.76
Sand = 0675
Gravel = 0.52

This means that in 1 m3 of gravel consists of pebbles m3 + 00:52 12:48 airspaces

Semen Bj = 1250 Kg
1 zak = 50 kg

concrete mixer concrete method to calculate BOW
=====> 1 m3 of concrete 1: 2: 3 so the mixture = 1 * 0.76 = .76 m3
2 m3 sand mortar finished --------> = 2 * 0675 = 1.35 m3
3 m3 kerikir -------> so mortar = 3 * 12:52 = 1.56 m3
==========================================
Material ---- produces 6 m3 = 3.67 m3 concrete

1 m3 of concrete = 1: 2: 3 ===> needed materials ...
-------------------------
Cement = 1.3.67 * 1 m3 = 0.2725 m3 = 340.5995 kg = 6812 zak
Sand = 1.3.67 * 2 m3 = 0.5449 m3
Gravel = 1.3.67 * 3 m3 = 0.8174 m3


=====> 1 m3 of concrete 1: 3: 5 to be slurry = 1 * 0.76 = .76 m3
3 m3 sand --------> so mortar = 3 * 0675 = 2025 m3
5 m3 kerikir -------> so mortar = 5 * 0:52 = 2.6 m3
========================================
9 m3 of material ---- produces concrete = 5385 m3

1 m3 of concrete = 1: 3: 5 ===> needed materials ...
-------------------------
Cement = 1/5.385 * 1 m3 = 0.1857 m3 = 232.1263 kg = 4.6425 zak
Sand = 1/5.385 * 3 m3 = 0.5571 m3
Gravel = 1/5.385 * 5 m3 = 0.9285 m3


=====> 1 m3 mortar plaster / mortar 1: 5 to be slurry = 1 * 0.76 = .76 m3
5 m3 sand mortar finished --------> = 5 * 0675 = 3375 m3
================================================
6 m3 of material - resulting slurry mortar = 0.76 + 3,375 = 4,135 m3

1 m3 of slurry mortar = 1: 5 ===> needed materials ...
------------------------
Cement = 1/4.135 * 1 m3 = 0.2418 m3 = 302.2975 kg = 6.0459 zak
Sand = 1/4.135 * 5 m3 = 1.2092 m3

EXPENSES calculated in BRIDGE PLAN

In general, the burden - the burden is calculated in the planning of the bridge is divided into two primary loads and secondary loads. The primary burden is a major burden in planning setipa stress calculations for the bridge, while the secondary load is the load while the resulting voltage - the voltage is relatively smaller than the primary voltage due to load and usually depends on the landscape, materials, construction systems, bridge type and local circumstances.

Primary burden of the bridge include dead loads, live loads and shock loads.

1. Dead load

Dead load is all cargo originating from its own weight of the bridge or bridge sections are reviewed, including any additional element is fixed that is considered one unit with a bridge. In determining the dead load weight of the volume should be used for building materials.

examples of dead load on the bridge: the weight of concrete, asphalt weight, the weight of steel, heavy masonry, stucco, etc. weight.

2. Living Expenses

Which includes the live load is the load that comes from moving vehicles, heavy traffic and / or pedestrians who considered working on the bridge. Based PPPJJR-1987, pages 5-7, the burden of living under review consists of:

a. Expenses "T" (Burden floor vehicles)

Expenses "T" is a load trucks that have a dual wheel load (Load Dual Wheel) by 10 tons, which works on the entire width of the bridge for vehicular traffic dingunakan.

b. Load "D" (Line traffic)

Load "D" is the arrangement of the load on each lane of traffic which consists of the load line "P" tons per lane of traffic (P = 12 tons) and the load evenly split "q" tons per meter length per lane as follows:

q = 2.2 t / m for L <30 m.

q = 2.2 t / m - {(1,1 / 60) x (L - 30)} t / m to 30 m
q = 1.1 {1 + (30 / L)} for L> 60 m.

Terms of use load "D" in the transverse direction of the bridge as follows:

§ To bridge the width of the vehicle floor <5.50 m, the burden of "D" is fully (100%) should be charged on the entire bridge.

§ To bridge the width of the vehicle floor> 5.50 m, the burden of "D" is fully (100%) charged to the line width of 5.50 m while the width of the remaining encumbered only half load "D" (50%).

examples of live load on the bridge: the burden of passing vehicles, loads of people walking, etc.

3. Shock load

According to Anonymous (1987:10) shock loads into account the influence of the vibrations of other dynamic effects., Stresses due to the load line (P) must be multiplied by the coefficient of shock. While the load evenly split (q) and the concentrated load (T) is multiplied by the coefficient of shock. The amount of shock coefficient is determined by the formula:

k = 1 + ((20 / (50 + L))

While the Secondary Expenses consist of wind load, brake force, and force due to temperature differences.

1. Wind load

Effect of pressure of work in the horizontal wind at 100 kg/cm2. In calculating the total area of ​​the bridge on each side of the vast number of parts used jembata on each side used the following provisions:

* For a full walled jmbatan taken as 100% on the broad side of the bridge
* To bridge order was taken by 30% against the broad side of the bridge.

2. Brake force load

This style works in the lengthwise direction of the bridge, due to brake and traction force are reviewed for both the traffic department. this effect is taken into account the influence of worth to the brake force at 5% of the charge coefficient D without shock that meets all existing traffic lane in one direction.

3. Due to the style of Temperature Difference

The temperature difference should be determined in accordance with local circumstances. Of C is assumed for the steel and concrete 10. Special review on the incidence of stresses due to temperature differences that exist between parts of the bridge with different materials.

4. Earthquake load

for bridge construction in areas affected by the earthquake, the earthquake load is also taken into account in the planning of the bridge structure

5. Wind loads

wind load is calculated on the bridge construction area that must withstand wind loads.

AutoCAD for Mac


AutoCAD, the industry-standard Computer Aided Design (CAD) application from Autodesk, is back on the Mac after an 18-year hiatus. This is lovely news for lots of Mac fans in the architecture, engineering, and design professions who have been reluctant to give up their MacBook Pros and iMacs for the sake of a single application, despite its status as a important part of their workflow. With the new Mac version of AutoCAD for freeform 2D and 3D design and drafting, Mac users no longer need to make use of Boot Camp or Parallels or suffer a PC on the same table with their Mac.



In lieu of offering the ribbon-based interface of the Windows version, Autodesk has has selected to place more AutoCAD functions in the pulldown menus. Floating gizmo palettes also include most of the same tools as the menus, while the interface will look familiar to users of other Mac CAD applications. Autodesk has also taken advantage of multi-touch trackpad gestures (& offers similar moves on Apple's Magic Mouse () For example, two-finger swipes scroll up or down, pinching can zoom in or out, & a shift and two-finger swipe can rotate around a 3D model. Cover Flow navigation lets you flip through your designs. Nice

AutoCAD 2011 for the Mac is not a port from Windows. , Autodesk has programmed this version for the Mac from the ground up with a conscious work to take advantage of the Mac OS X interface.

While AutoCAD is a complex and powerful application, the technique requirements are higher than much of the competition on the Mac (such as Vectorworks (), TurboCAD (), and Ashlar-Vellum), beginning with a maximum of 3GB of RAM and higher screen resolution (1280 x 800 pixels). The program works with only with more recent Mac hardware such as Mac Pro (early 2009), MacBook Pro (mid-2009), and iMac (early 2008). To be fair, you'd require to make use of a high resolution monitor with a CAD program anyway, given the quantity and level of graphic detail you are usually working with. But, you are less likely to be disappointed with AutoCAD's performance in case you bought your Mac in the last couple of yearsWhile AutoCAD is a complex and powerful application, the technique requirements are higher than much of the competition on the Mac (such as Vectorworks (), TurboCAD (), and Ashlar-Vellum), beginning with a maximum of 3GB of RAM and higher screen resolution (1280 x 800 pixels). The program works with only with more recent Mac hardware such as Mac Pro (early 2009), MacBook Pro (mid-2009), and iMac (early 2008). To be fair, you'd require to make use of a high resolution monitor with a CAD program anyway, given the quantity and level of graphic detail you are usually working with. But, you are less likely to be disappointed with AutoCAD's performance in case you bought your Mac in the last couple of years.

When you first launch AutoCAD 2011, you will be introduced with the drawing canvas or Modelspace, the window where you will build your drawing or model. The menus are extensive, and the gizmo and information palettes are arranged to the left and right of the canvas.

of the first things you will notice is that the default background in AutoCAD is black or slate-colored with the lines and objects you draw in white (or bright colors). This differs from most Mac CAD or graphic design applications, which usually have a white background with black and color drawing elements on top. You can change the background color in the preferences and, in fact, much of the interface can be altered to fit your own tastes, including which tools show up in the palettes and where the palettes can be found on screen.

One interface element Autodesk brought over from the Windows version is the ViewCube, a useful graphical navigation element for controlling 3D views. It lets you rotate your drawing & model, or jump to standard 3D views & orientations with a single-click. The ViewCube rotates as you click on it, giving you a visual representation of your drawing at various angles. Moving around a 3D model can be disorienting, & the ViewCube does a lovely job of letting you know whether you are looking from above, below, or at some oblique angle.

Another uniquely AutoCAD interface element is the Command Line window. This has been an AutoCAD mainstay for lots of years. At first it looks like some DOS operating process throwback, but it is actually a very useful window because it displays in text format everything that is going on while you re drawing, line-by-line, command-by-command. Interestingly, it can operate both ways: you can enter text commands in to the window & control your drawing from the command line while maximizing the use of the keyboard & minimizing use of the mouse & menus. While overall that method of operation is not very Mac-like, in case you have been using the Windows version of AutoCAD for a very long time, this feature will be welcome.

From the Mac point of view, though, my largest complaint about the interface is that the method of drawing objects often includes more clicks than necessary, & can need the use of the keyboard.
For instance, drawing a simple line is not as simple as choosing the line gizmo and then clicking and dragging to generate the line. In AutoCAD, to finish the system of drawing the line, you require to hit another key such as Escape or Enter, or the Space Bar after the second click. Otherwise, you will keep adding more lines. Then, in the event you require to draw another line elsewhere, you require to pick the line gizmo again. No doubt, this is something you can get used to, but Id not must click so much.

While plenty of CAD programs can import & export DWG files, these translations sometimes need cleanup. Not having to worry about cleanup or whether your exported DWG files will open correctly is actual advantage of AutoCAD for Mac over other Mac CAD programs. I opened numerous DWG files received from Windows consultants I work with & AutoCAD for Mac opened most of them seamlessly. However, I did run in to a tiny number of drawings that necessary parts not obtainable for the Mac, such as some (but not all) ObjectARX parts my civil engineer makes use of. Some of these parts, made by third-party vendors, are widely used & personalize & extend AutoCAD. I hope that the developers of such parts update them for use on the Mac.

One of the reasons plenty of architecture firms use AutoCAD is the popularity of its file format. The DWG format native to AutoCAD is often used for collaborative work across a broad range of professions such as consultants, architects, and engineers.

This brings up the subject of add-ons for AutoCAD. thing that makes AutoCAD for Windows such a dominant product are all of the third-party extensions obtainable. In the Windows version, there's add-ons & extensions obtainable for any profession or specialty, & there's thousands of tools & scripts that you can add to AutoCAD that provide even more capabilities than are included in the basic application. A number of the add-ons are already obtainable for the Mac, but today, most are not. For example, I ran in to some missing extensions while trying to import AutoCAD files from a civil engineer I work with. Autodesk says it is working on having more extensions obtainable for later releases of the Mac program, & will be making the development of add-ons feasible on the Mac.

Like PDF, there's dozens of features in the Windows version that are not included in the Mac version. A quantity of them are important features such as Plot Style Configuration, Plot to File, or the Reference Manager.

One glaring feature missing from AutoCAD 2011 is support for importing and exporting PDF files. In the current version, there is no export or print-to-PDF feature from within AutoCAD. Using the print-to-PDF option in the standard Mac print dialog box gives poor results compared to other CAD programs with built-in PDF support (including AutoCAD for Windows). There is also no way to import a PDF file in to your drawing, another feature supported in the Windows version of AutoCAD, but not on the Mac.

With this first comeback version of AutoCAD, Autodesk appears to be applying the 80/20 rule for its Mac users, providing the 80 percent of features and tools that are used the most. I don't have a conceptual issue with that approach. It seems sane for such a immense program to implement the most important parts first and then fill inOn a positive note, Autodesk has a free iPhone/iPad app available in the iTunes store that lets you share and view AutoCAD files in the field. You may even do some light editing of the files right on your iPhone or iPad, including drawing new objects, moving, rotating, and annotating.

Tuesday, December 27, 2011

Low Cost Steel Detailing and Structural Steel Design Services


Outsourcing Steel Detailing firm is a leading steel design service provider company specializing in steel structure designing & steel detailing services. They offer custom-tailored 2D & 3D Steel Designing & Detailing solutions to help you turn today's challenges in to competitive advantage. They use application like AutoCAD, AutoSketch, Revit, Tekla, etc & web-based collaborating tools to provide you the benefits of low operating cost, superior services & efficient delivery schedule.

Steel structures are widely used in steel building designs & construction of residential steel building design. Structural Steel detailing is useful for all kind of steel structures ranging from residential buildings to massive commercial buildings. Steel structures can be designed or planned basically with less hard work & provides advantages like sturdiness, durability & portability. Structural steel services include designing dimensions & detailing of various Post-tensioned, Precast concrete detailing, Pre-stressed & Composite steel structures in accordance with industry standards & codes.

They have a massive pool of highly qualified steel detailers & structural steel engineers producing correct drawings of each structural element, their placements, connections between them & exact dimensions. This involves detailing of steel staircases, beams, plates, columns, bar joists, stack, decking/grating, etc. Our methodology is well defined & technique & result oriented. They put our best hard work to establish fruitful business partnership with our clients by ensuring exact, correct, high quality steel detailing services within the budget & on time.

They provide structural steel designs for industrial structures such as:
Steel buildings
Residential/Commercial buildings
Residential Steel framing
Warehouses
Sheds/Shelters/Roofs
Office blocks
Support structures
Floor systems/Mezzanines,
Miscellaneous Steel structures

Factors to be considered in the design of steel structures


All the members in the structure ought to have adequate strength, stiffness & toughness to be sure proper funtioning in the work of service life. Members ought to have adequate strength, stiffness & toughness to be sure propoer functioning in the work of service life.

Reserved strength must be obtainable to cater for:

Aim is to prevent limit state from being reached.
one. Adaptations to site:

Occasional overloads - underestimated lots
Variability of strebgth of materials from those specified.
Variation in strength due to workmanship, construction practices.

If the structure is a building, for example, the designer must generate a plan that has suitable arrangement for rooms, corridors, stairways, windows, elevators, emergency exits etc & all this plan ought to be adapted to site so that it is feasible, accepted aesthetically & at a reasonable cost. This is called funtional planning.
two. Structural system:

structural system is dependent on funtional planning. Structural system includes the location of columns in the buildings, it is to be worked out with the funtional plan & sufficent space must be anticipated between completed ceiling & completed floor for location of columns.
three. Structural analysis:

One time lots are defined & design is laid out, structural analysis must be performed to choose internal forces that will be produced in various members of the framework. Assumptions must be made & it ought to be ensured that structure in point of fact also behaves as it is meant to (& as it was assumed to behave).
four. Proportionality of members:

Members must be proportioned with factor of safety in mind.
five. Factor of safety:

Variability of the material with respect to strength & other physical properties
Uncertainity in the expected lots
Precision with which internal forces are calculated
Possibility of corrosion
Extent of damage, loss of life
Operational importance
Quality of workmanship

The development of design specifications to provide suitable values of the margin of safety, reliability & probability of failure must take in to consideration the following factors.

Advantages of LRFD


LRFD accounts for both variability in load and resistence. It achieves uniform levels of safety for different limit states.
Comparison of ASD & LRFD

Advantages of LRFD

ASD is the simple technique & LRFD is the sophisticated.
ASD combines dead and live lots and treats them in the same way.
In lrfd different load factors are assigned to dead lots and live lots, which is appealing.
Changes is load factors and resistence factors are much simpler to make in lrfd.

Mechanical properties of structural steel

Material
Length
X-section

Resistence to deformation based on:

Design technique

Preliminary member sizing of beams
Structural analysis - modeling, analysis
Design review - member modifications
Cost of estimation
Preparation of structural drawings and specifications
Lots for structural analysis and design
Dead load
Live load
Mean return period OR
Recurrence interval OR
Live lots for various occupencies
Reduction in basic design live load
Impact Load
Wind load

Load & Resistence Factor Design




It considers the variability not only in resistence but also in the effects of load.
Provides measure of safety relative.
Safety in the design is obtained by specifying that the reduced nominal strength of a designed structure is less than the effect of factored lots acting on the structure.

Redundancy:

Ability of a structure to go through in-elastic deformation without rupture.

Ductility:

It is the ability to resist abrasion.

Steel Strength:

it is the ability to redistribute the load. Simple beam is determinate. Fixed beam is indeterminate by two degrees so it's redundant actions. fixed supported beam is more better as indeterminate structure can redistribute the load. When load increases support becomes plastic & it turns in to a basically supported beam. But basically supported does not go through the stage of plastic hinge they fail directly.
Hardness:

Ability of a structure or structural part to absorb energy.
Fatigue:

Maximum load which an object can resist. OR it is the maximum load that the steel can resist before failure. Steel is said to be failed when it's yielded. It is thus called yield strength
Toughness:

It is a progressive, localized permanent destroy under fluctuating stress.

Structural Steel Design & Construction of Steel Structures



Design philosophies

A. Allowable stress design
B. working stress design (for concrete)
C. final stress design


What is meant be the design of structures?
Is it an arbitrary or scientific technique?
How to design a structural technique?
Parameters involved in the design?
What is meant by demand on structural technique & what is capacity of a structure?
Is demand related to capacity?

What are the requirements of steel design?

Topics to be studied & ideas to be learned

Demands: Snow, earthquake, live load etc.
Limit state:

A condition beyond which a structural technique or a structural part ceases to fulfill the funtion for which it is designed.
Examples of limit states :

A. Deflection
B. Fatigue
C. Shear
D. Buckling
E. Bearing
F. Cracking
G. Flexure
H. Torsion
I. Settlement
J. Stability

Strength limit states :
A. Flexure
B. Shear
C. Torsion

Serviceability limit states :
A. Cracking
B. Excessive deflection

Wednesday, September 7, 2011

How To Test Soil




I. PURPOSE
• Pricing Field Dry Weight Content.
• Determining the Degree of Soil Density.

II. BASIC THEORY
There are several methods used to calculate the weight of the contents of the field. Standard procedures used include:
a. Sand cone method
b. Rubber Balloon Method
c. Use of Nuclear Density Measurement.
Cone of sand (sand cone) consists of a plastic or glass bottle with a metal cone that is placed on it. Plastic bottles and cones of sand in dry Ottawa sand fill with sand, which is a standard that has a uniform gradation.
On the field made a small hole in the tube-shaped land that has been compacted. After the holes were dug, soil is weighed entirely original, with a bottle filled with sand cone placed over the hole so that it can obtain the contents of the dry weight of the compaction.

III. EQUIPMENT AND MATERIALS
Equipment
1. A set of tools sand cone.
2. Scales with 0.01 gram accuracy.
3. Cylinder of known volume.
4. Cans with lids
5. Term sliding
6. Meter.
7. Digger, shovels, spoons, screwdrivers, knives, etc.

Material
Ottawa sand with a uniform diameter and dry.

IV. STEP WORK
A. Determine the weight of sand in the funnel. (Wps.cr)
1. Prepare the equipment needed, by placing the bottle and funnel.
2. Ottawa sand bottles filled to the brim, valves closed and the remaining sand is cleaned and then weighed (W1) with the funnel in place.
3. Place on a flat field with the funnel facing down.
4. The tap is opened up to sand down and fill the funnel, after full faucet is closed.
5. Bottles plus a funnel and the remaining sand and then weighed (W2)
6. Then the weight of sand in the funnel is:
7. Wps.cr = W1 - W2

B. Determine the weight of sand in the cylinder (Wps.sl)
1. After the move, place the bottle on a cylinder that has been known volemenya (with the funnel facing down)
2. The tap is opened up to sand down to fill the cylinder and funnel, when the cylinder is estimated to have been fully tap is closed.
3. Bottle and funnel along with the rest of the sand 2 is calculated (W3)
4. Then the weight of sand in the cylinder
Wps.sl = W3 - Wps.cr

C. Determining the content of the dry weight of sand. (Γps)
How to calculate the weight of the contents of dry sand is by dividing the weight of sand in a cylinder with a cylinder volume, then:
γps =

D. Determine the volume of the cylinder (Vsl)
1. Calculate the weight of the cylinder (WSL)
2. Then calculate the volume of the cylinder, by measuring the radius (D), & high (t).
3. Then the volume of the cylinder is:
Vsl = ¼. Π.D2.t

E. Determine the volume of pits (VLB)
1. Full contents of the bottle in the sand plus the funnel and then weighed (WA).
2. Prepare digger and plastic.
3. Ground surface, at a predetermined point leveled and cleared.
4. By using the mall, made a hole as deep as 10-15 cm. In accordance with the height of the cylinder used to measure the weight of the contents of dry sand (B). All soil excavation should be collected in plastic, there should not be wasted and taken care not to change their water content (plastic while closed).
5. Place the bottle over the hole with a funnel facing down. Faucet is opened up to fill holes and sand down a funnel.
6. After the sand from the bottle does not go down anymore, faucets are closed, then weighed the bottle along with the rest of the sand (WB). Meanwhile above ground the excavation immediately weighed and measured water content in the soil until the hole is known weight (W), and its water level ()
7. Obtained the weight of sand in the funnel
Wps.cr = WA - WB
8. Calculate the weight of sand in the hole
Wps.lb = WC - Wps.cr
9. Volume obtained by dividing the weight pit of sand in the sand pit and gamma
VLB =
F. Determine soil moisture content pit (ω)
1. Bring on the ground that had been dug into the field laboratory
2. Take 3 small bowls of fruit and calculated weight (WC).
3. Put some soil samples dug into 3 small bowls and weigh weighing each - each (Wctb).
4. After that enter the 3 bowls which already contains the soil into the oven for ± 24 hours.
5. The next day took the cup from the oven and weigh weight (Wctk).

6. Calculate the weight of water contained in the land
Wair = Wctb - Wctk
7. Calculate the weight of dry soil excavation
WTK = Wctk - WC
8. Water content obtained by dividing the weight of water and dry soil weight multiplied by 100%
ω =
G. Determine the dry weight of the contents of the field
1. Bring the excavated soil in field and calculate the weight (Wtn.lb)
2. Calculate the height, diameter, and volume of pits.
3. Gammanya Calculate by dividing the land between the weight and volume of the hole.
γ =
4. Calculate the dry unit weight by dividing the field between the gamma and levels of water plus 1.

Friday, August 5, 2011

Why CAD Desingning Software


In engineering area planning and designing play crucial role in the accomplishing of every project. In civil engineering field building design drawing is necessary and ought to be carried out correctly as soon as feasible. Draftsmen and drafters are specific positions that usually do the building construction drawing.

CAD drawing and designs usually signify to drawing and designing structures in digital format that utilize the latest building drawing program. Drawings generated from the program extensively used by civil engineers to get insight about the building specification or what is called design designs. Architecture specialists have established a guideline for building construction drawing and explained it as building's technical drawing. The work of construction is progressed by using these technical ideas and drawing. All mandatory elements such as different views, layouts, cross referencing as well as units of measurement can be obtained using the CAD design drawing. CAD designing professionals can basically accomplish the design understanding and dimension specification.


The CAD or Computer Aided Design drawings are chiefly technical drawing building program for drawing building designs. The program can make working drawings from raw knowledge and therefore civil engineers can draft comprehensive specification and technical drawing sheets using it. The Auto CAD drawings are offered from blue prints to hand drawn sketches. Complete drawing of building can be made from common layout sketches along with details like electrical designs, furniture designs, floor finish designs, elevations, reflected ceiling designs, point of view and more.

CAD building drawing program is necessary to receive correct estimations that include estimation of costs from the outset of construction designs or working drawing. Various materials' volumes that are needed can be given if the material quality specification is given along with its current rates.


Today the introduction of 2D and 3D know-how bring impacts to CAD building drawing program and improve its ability to produce quality sheets with the help of computer know-how. The program allows civil or architecture engineers to reduce the redesigning possibility that therefore will save more time. This modern program definitely can make lots of works by professional architects and drafters can be done basically in building designs. The application of the program is from residential to commercial projects. All kind of construction drawings that need layouts, 2D and 3D presentation, elevations and details can take advantage from CAD. CAD drawings have catered the actual estate makers, actual estate owners, contractors as well as consultants

Guides of Drawing Numbering Technique in Civil Engineering


Preparing drawing is the common task of a civil engineer. Drawing of a building is performed after the structure design has been completed. Having the right drawing numbering technique is important in the whole building construction technique in order to get better presentation. Here they will discuss about some important guides of drawing numbering technique in civil engineering.


The first important tip is numbering by using time control. That means a project ought to have timeline in month & year about when it starts & when it stops. Such timeline is useful so you can control over your building design drawing & make it traceable. For an instance, in case you receive a project on say three June 2008, your drawing number ought to not be 30602008 but must 062008. The reason is that the first number has more chances to become complicated. As control item, you can select the year of the awarded project, 2008. In that case, your preliminary building drawing is 062008. The second advice you can take is the use of client name control. For example, if your client name is AAA Company, by combining the time & client name controls you can get a building drawing number of AAA/062008.


As addition guide, you can use engineering field control for your building design drawing. If your current project is to build a structural building, you can use the abbreviation of structural building, 'ST' for your drawing number. Therefore, your new drawing number will be AAA/062008/ST. Other abbreviations that are often used in civil engineering sectors are 'EW' for earthwork, 'WT' for water work, 'SW' for sewer work,'DR' for drainage work & more.


Structural element control can be used in numbering your building design drawing. The structural elements here include column, pad footing foundation, slab & more. For beam you can use 'BM' abbreviation, 'SB' for slab & more. If for example the beam detail is showed by your building construction drawing & it is the first drawing, then AAA/062008/ST/BM01 will be your drawing number.


The last part in drawing numbering is the drawing amendment. If on particular sheet of your building drawing there is an amendment you can use the abc notation to show every amendment available on your drawing. For example to show the first amendment to your existed number, AAA/062008/ST/02, you will use AAA/062008/ST/02a, while for the second amendment you will use AAA/062008/ST/02b. In conclusion, they can draw a formula for your drawing number as: [(client name)/(month year)/[(engineering field)/( element type)(number)(amendment).

This Editorial is about: Drawing of a building, building construction technique, civil engineering, building design drawing, building drawing, building design drawing, civil engineering, building drawing

Thursday, August 4, 2011

Factors On The Salary Of Civil Engineering


In today's life, engineering has become a pool of the most luring jobs all over the world. Civil engineering, of the main groups in engineering has been beautiful for plenty of students to take admission in plenty of high-class engineering institutes throughout the world. Jobs in civil engineering do not only demand a sizable amount of creativity & challenge but also offers a nice income or wage as well as high positions.

Despite of offering bright career path, civil engineer is of the hardest jobs since it involves high load or work that includes building design drawing, work planning, resource assessing, researching & more. An expected wage of a civil engineer with considerable experience is beginning from about $75000. Therefore, the lower level position in civil engineering can expect lesser than that amount. Based on knowledge from National Association of Colleges & Employers in Pennsylvania, United States, obtained in April 2010, graduates from civil or architectural engineering can get a beginning wage of $52,443. The average number appears to be unaffected from the economic recession since when other professionals get declining wage range, this average number of wage of engineering graduates get wage rise of one.3%.

In Indonesian civil engineering sector, civil engineers that work as consultants both in public & private segments usually get an beautiful wage & so do they in Indian's & any other countries. In India, the salaries of these individuals who work using building construction process that work in the sector of government get nice wage with range from Rs 8,000 to Rs 12,000. By experience, those engineers may expect their salaries to go up to reach a range from Rs twenty,000 to Rs 25,000 a month. Further, in the same country engineers that work for private sectors often get a every month wage that is about Rs 30,000 while the experienced ones may command every month salaries that range from Rs 50,000 to Rs 60,000.

Is about: Civil engineering, building design drawing, civil engineering, Indonesian civil engineering, building construction process, drawing building designs, technical drawing building program for drawing building plans

Civil engineers who work in specific or specialized field such as surroundings, infrastructure, hydraulic & others that may involve bigger risks can expect a great wage. Engineers that have additional knowledge such as drawing building designs are highly regarded. Knowledge about technical drawing building program for drawing building designs will make them get an additional point. In short, the factor that influences the amount of salaries among civil engineers closely related with on the length or the type of the projects that they are working for. More qualified & experienced civil will deserve for beautiful remuneration as well.

Role Civil Engineering In Industry



Construction engineering is thought about of the oldest segments in industrial sectors. It stands high in contributing an essential amount to the society's development. Civil engineering is a field that greatly supports human civilization for lots of years. By generating important infrastructures like roads, dams, high buildings, & more civil engineers have evolved in significant timeframe to demonstrate their greatest potential.

A though work is involved in the construction engineering jobs. That is known well by recruitment agencies that have specialization in manufacturing or construction sectors.

Over that construction engineering has been playing a compulsory role in the nation development all over the world. This area offers luring career path as well. In civil engineering there's stages of works including drawing, designing, planning, translating as well as implementing constructional jobs. Civil engineer is a profession that involves a variety of engineering activities like planning, inspecting & other structural activities dedicated for public segments like constructing buildings, roads, airports, bridges, harbors, tunnels. From time to time, construction engineering offers a immense amount of demanding career chances.

To be a skillful, professional & professional civil engineer, has to possess deep knowledge about building construction process. Civil engineers are the 'captains' behind the industry development that therefore recruiting companies ought to pay additional attention when they recruit professionals in the field of construction engineering. It is important to receive a who has strong knowledge about the whole process of constructing structures, from drawing building designs to the final inspections. Consultants in engineering recruitment provide their expertise in finding skilful, gifted, creative & innovative candidates to be able to deliver their best expertise & potential as well as to contribute to their company & the nation great level of success.

Computer & application knowledge is usually a common requirement in construction engineering field. Particular knowledge about building drawing application is a and in the civil workforce. The reason is that such knowledge is proven to be beneficial in cutting the wasted time coming from long process of drawing of building including redesigning due to manual error in the building drawing process. Over that, the building drawing application is also beneficial in keeping with the important construction codes at a local level in the country.

Construction engineering in the industry has specific employment patterns. The recruiter consultants usually have in-depth knowledge in lots of aspects of resourcing, transportation, geo technical, surroundings & more. That is all needed so that they know exactly the qualities needed in civil workforce & can recruit the potential & right individual that suits for obtainable position in this segment.

Sunday, July 17, 2011

Construction Document Services


Structural drawings with design calculations:
Foundation Plan
Details of Roof Truss & Joist
Details of Tanks, Chimney, Bunkers, Silos, etc.
Details of Blown up connections
Standardized Bar Bending schedule
Drawings of Pre-stressed structure
Measurement sheet of quantity estimation
Full Tendon profile

Structural Drafting Firm provides reliable construction documents services & construction documents management at competitive rates. Our in-house team of engineers & CAD operators delivers quality construction documents & CAD drawings as per the country specific planning & building code requirements. They also offer specialized construction documentation services like coordinated drawings which integrates mechanical, electrical, architectural & structural drawings in to set of drawings.
Our construction documents services includes:

Structural Drafting Firm aims to provide construction documents services at 100% precision using leading edge technologies (Tekla, AutoCAD, AutoSketch, Revit, Photoshop, etc) & country specific codes (AIA Standards, ASME, BS codes, etc). They have well defined methodology which is system driven & result oriented. Our team strictly complies with the specifications provided by your architects, structural engineers & consultants to generate standardized construction document project manuals.

Architectural Drawings:
Site location layout showing major building parts & sections
Civil drawings like designs, elevations, sections, details & specifications
Interior drawings like designs, elevations, lighting, furniture layouts, etc
Axonometric drawings

The company offers flexible & tailor-made solutions to fit your needs & requirements for all cost points. They work for clients on fixed & man-hour pricing models depending on the complexity & volume of work. They have high-level project development & management support - leaving clients to focus on the remainder of their business.

Design Audit


They also make definite that your design meets ergonomic standards so that there's mobility & operating clearances between equipment, furniture & other design elements of the floor & space designs. For every piece of equipment & furniture you propose to be in your floor plan, they research its usage requirements to make definite it functions well with work processes & occupant traffic flow.

With Classical Drafting's design audit service, they check your proposed design against all applicable permitting codes, including building, health, fire, plumbing, mechanical & handicap codes, among other codes, to make definite the feasibility of your design. They can understand your design intent & will offer solutions to design conflicts that both maintain the integrity of your design while meeting code requirements.

Design Audit aligns: 

Brand design
Information design
Service design
Corporate design (which integrates product, information and environment design)

3D Modeling


3D drafting is the latest in drafting know-how. It is based on the idea of BIM ' Building Knowledge Model ' in which a virtual 3D model of a building is created. Knowledge is then extracted from the model to generate building designs, 3D renderings & animation. 3D know-how is faster than 2D drafting, more correct & has lots of benefits. The benefits to drafting in 3D can be seen in the technique of generating designs, which is as follows:



Buildings are modeled using 3D digital elements such as walls, windows, doors, roofs, cabinets, appliances & any other aspect of a building. One time the model is created, any view & any amount of knowledge can be extracted from the model.
The model can be sliced horizontally to view the floor plan.
The model can be sliced vertically to view wall & building sections.
A bird's eye view of the model can be shown to generate the roof plan.
Elevations can be automatically generated from the model.
The 3D digital elements that make up the model store knowledge which can be extracted in to schedules & tables such as window & door schedules.
Materials such as brick, stucco, paint, roof tiles or any other material can be applied to the 3D digital elements of the model to generate full color 3D renderings & animation.


Classical Drafting makes use of AutoDESK products 'AutoCAD, AutoCAD Architecture (formerly called Architectural Desktop 'ADT) & Design Review

If any changes are made to any element of the building, the changes are automatically reflected in all designs, sections & schedules & in other parts of the plan set. Making changes is necessary in place, for example, adding or changing a door, & the changes are automatically reflected in every single place else in the designs ' on the floor plan, on the elevations, on the door schedule & in all other places where the door appears in the designs.

The Building Design Methodology


Structural Drafting Firm is India-based leading Building Information Modeling solutions provider catering to project information and visualization needs of engineers, architects and consultants. They have an in-house team of 100 experienced draftsmen, structural engineers and CAD operators who work closely with engineers and building contractors to deliver highly smart BIM models, construction drawings and visualizations using Building Information Modeling (BIM) expertise.

Building Design, Building Information Modeling or BIM is an innovative approach to manage and represent building information information such as its structural parts, spatial relationship, construction sequences, etc in digital format. BIM modeling develops a 3D virtual model for building's architecture using sketches and renderings. It constricts building design lifecycle by improving coordination among engineers, architects, contractors and building owners.
BIM Services - Building Information Modeling include:
Virtual Building Modeling
Architectural BIM Services
Structural BIM Services
HVAC and MEP BIM Services
Construction Documentation
Clash Detection and Risk Mitigation

Through the built-in BIM methodology they make it simple for all the stakeholders to create, evaluate and document building designs right from the conceptual phase through the facility operation, construction phase, and beyond. They are the cease location for all of your BIM modeling requirements. Contact us today!
Application Expertise:
ArchiCAD, Revit, Tekla and Microstation
Project information extracted by a BIM Model can be utilized for various purposes like:
3D CAD Modeling and Rendering
CAD Drafting in 2D
CAD interoperability support for engineering coordination.
Verifying information on building geometry, interior design, project sequencing and scheduling.
Advantages of BIM Services:
BIM Modeling decreases construction costs by enabling quantity surveys.
Improves coordination between all involved parties
Production of high quality set of construction documents
BIM modeling enhances the quality of construction by facilitating pre-fabrication of different parts
BIM method helps in mitigating risks through real-time clash detection